La-OMS-2催化剂催化甲苯氧化制苯甲醛

合成了氧化锰八面体(OMS-2)分子筛,采用离子交换法和浸渍法制备了稀土金属La改性的OMS-2分子筛(La-OMS-2)催化剂,并用于甲苯液相选择性氧化制苯甲醛,考察了催化剂用量、反应温度、反应时间、氧气流量及溶剂种类对甲苯转化率和苯甲醛选择性的影响,对La-OMS-2催化剂进行了X射线衍射表征和BET比表面积测定。实验结果表明,离子交换法制备的La-OMS-2-A催化剂的活性高于浸渍法制备的La-OMS-2-B催化剂,在甲苯0.1mol、溶剂冰乙酸10mL、氧气流量60mL/min、La-OMS-2-A催化剂用量0.10g、反应温度353K、反应时间1.0h的条件下,甲苯转化率达61%,苯甲醛收率为56%。加入La对OMS-2分子筛中的MnO晶格结构产生了影响,提高了苯甲醛的收率。     

Optimization of anodic oxidation and Cu–Cr oxide catalyst preparation on structured aluminum plates processed by electro discharge machining

This paper describes the optimization of three processes applied in fabrication of a microstructured reactor for complete oxidation of volatile organic compounds. The first process involves the optimization of the electro discharge machining (EDM) method to produce a set of microchannels with a high length to diameter ratio of 100, with a standard deviation from the average diameter below 0.2%, and with a surface roughness not higher than 2.0 μm. To satisfy these criteria, fabrication of microchannels must be carried out with two machining passes in the Al51st alloy. Then, the effect of several parameters on the anodization current efficiency with respect to oxide formation was studied. The best process conditions to get a 30 μm porous alumina layer in a 0.4 M oxalic acid electrolyte, were found to be a temperature of 1 °C, an anodic current density of 5 mA/cm², and 23 h oxidation time. At last, the resulting coatings were impregnated with an aqueous solution of copper dichromate followed by drying and calcination at 450 °C to produce active catalysts. The effect of a copper dichromate concentration, number of impregnation cycles (1 or 2), and different after-treatments on catalytic activity and stability in complete oxidation of n-butane were studied. The catalytic activity of the obtained coatings is superior to that of alumina supported pelletized catalysts even at much lower loadings of active metals.     

Effect of carbon surface oxidation on platinum supported carbon particles on the performance of gas diffusion electrodes for the oxygen reduction reaction

The effect of carbon surface oxidation on platinum supported carbon particles (Pt/C) with nitric acid was investigated by cyclic voltammetry, electrochemical impedance spectroscopy, polarization experiments and chronoamperometry. Cyclic voltammograms, polarization curves and electrochemical impedance spectra showed that the treated catalyst had much larger active surface area and higher ionic conductivity than the untreated catalyst, and provided enhanced performance for oxygen reduction. The formation of acidic groups was examined by IR spectra. The Pt/C surface oxidation had a large effect on the performance of a gas diffusion electrode for oxygen reduction reaction.     

Anodic oxidation of mecoprop herbicide at lead dioxide

The electrochemical oxidation of an aqueous solution containing mecoprop (2-(2-methyl-4-chlorophenoxy)propionic acid) has been studied at PbO₂ anodes by cyclic voltammetry and bulk electrolysis. The influence of current density, hydrodynamic conditions, temperature and pH on the degradation rate and current efficiency is reported. The results obtained show that the use of PbO₂ leads to total mineralization of mecoprop due to the production of oxidant hydroxyl radical electrogenerated from water discharge. The current efficiency for the electro-oxidation of mecoprop is enhanced by low current density, high recycle flow-rates and high temperature. In contrast, the pH effect was not significant. It has also been observed that mecoprop decay kinetics follows a pseudo-first-order reaction and the rate constant increases with rising current density.     

Oxidation of some aliphatic polyols on anodically deposited MnO2

Galvanostatic steady state current potential measurements were carried out for oxidation of a series of aliphatic alcohols having varying number of hydroxyl groups. The anodically deposited layer of MnO₂ on platinum was used as the electrode material. The deposit was characterised by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX) and electrode potential measurements. The catalytic role of MnO₂ in the electro-oxidation of alcohols was indicated by the chronopotentiograms and the cyclic voltammograms. An analysis of the electrochemical data indicated a catalytic EC mechanism in which Mn (V) is generated electrochemically and consumed chemically in succession. Based on this and the hydrogen bonding interaction between alcoholic hydroxyl groups and MnO₂ layer, a mechanism was proposed which accounts for the variation in the observed electrochemical reaction orders. Tafel behaviour was found to be followed only approximately. Current efficiency of the electrochemical oxidation of polyols was studied. Replacement of platinum by carbon as current collector was found to leave the electrocatalytic activity of the MnO₂ deposit practically unaltered.     

Electrochemical behaviour of phenylethanolamine at gold in aqueous solution

The electrooxidation of phenylethanolamine (2-amino-1-phenylethanol) at a gold electrode in alkaline electrolyte has been studied. Measurement of the differential capacitance of the electric double layer versus the electrode potential has shown that the adsorption of phenylethanolamine at the gold-solution interface plays a significant role in the oxidation mechanism. The effect of amine concentration, electrolyte pH and potential scan rate on the electrooxidation is analysed.     

Study on Preparation and Application of Ti／Si Complex Zeolite

A Ti/Si complex zeolite has been prepared. X-ray diffraction and infrared spectrometry study has shown that two structures, namely the ZSM-5 and MCM-41, exist in the sample. BET tests have revealed that the complex zeolite contains regular mesopores of 2.6 nm. Ultraviolet spectrometry analysis has shown that the Ti species exist in the zeolite skeleton in the form of tetra-coordinate valence. The Ti/Si complex zeolite (TS-1/Ti-MCM-41) has apparently improved catalytic activity with respect to the macromolecular organic compound oxidation as compared to individual components of either Ti or Si containing zeolites (TS-1 and Ti-MCM-41).     

碳铬镍含量对高铬铸铁测温保护管性能的影响

通过高温氧化和高温磨损实验,研究了C、Cr、Ni 3个主要元素对高铬铸铁在高温条件下抗氧化和抗磨损性能的影响。结果表明:Cr含量越高,抗氧化性能和抗磨损性能越好;提高碳含量,明显提高高铬铸铁的高温抗磨性能;当w(Cr)=16％时,加入Ni能提高高铬铸铁的高温抗氧化性能;w(Cr)=30％时,Ni对高铬铸铁的抗氧化性能和抗磨损性能影响不明显.在1100℃以下,选用w(C)=2.8％,w(Cr)=30％、不加Ni的高铬铸铁铸造高温抗磨热电偶保护管,既有较好的使用寿命,又可降低成本.     

液化气催化氧化脱硫工艺的工业应用

介绍了MOYOX法液化气催化氧化脱硫工艺的工业应用情况。应用结果表明，该工艺流程简单，操作灵活，脱硫效果显著，硫含量可降至3mg／m^3，含硫平均脱除率由74．2％提高为97．7％，铜片腐蚀也得到了明显改善。     

Cu-Cr合金高温氧化行为分析

该文用热分析天平，结合金相、X射线衍射(XRD)、扫描电镜(SEM)和能谱(EXD)研究了Cu—Cr合金在不同温度下的氧化行为。结果表明，Cu—Cr合金在700℃-900℃氧化符合抛物线规律，其最外层氧化膜为CuO，内层为Cu2O和Cr2O3，铬有助于提高合金的抗氧化能力。